How’s this? You’re hanging out with your compañeros, enjoying some cigars, drinks, snacks, etc., and you reach one of those moments when everyone goes silent. Here are my picks for the top 10 cigar smoking tricks you can do with your cigars to liven up the mood. Continue reading
Not too long ago, I wrote an article for CigarAdvisor.com about how I used an ordinary household condiment to repair a wrapper that was unfurling on my cigar. The way it happened was, I had mistakenly clipped the cap of my cigar a bit too low. I’ve seen some guys chop their cigars below the shoulders and the wrappers have remained intact. However, more often than not, over-cutting the cap will result in unraveling of the wrapper leaf, which is what happened in my case. Even more annoying is when this happens to a really fine (and not to mention, pricey), cigar. Continue reading
When you light-up a cigar you probably don’t think very much about how you light it. Well, as a “professional cigar smoker,” this is one of the things I do think about, so I thought it might be fun to look at the different techniques people use to light their cigars.
Before I get into them, here are a couple of things to keep in mind with regard to flame. The blue portion of the flame is the hottest. This is why torch lighters are so effective for lighting cigars. Moreover, this uber-hot flame permits you to “toast” and light your cigars without scorching them. As described below, if you can help it, you really don’t want the flame touching the tobacco. That’s especially important in this case, because the blue flame is so hot, you can hold the torch several inches from the foot of the cigar and still get a really good light.
That brings us to the white part of the flame. This part of the flame is pretty damn hot, too. Want to find out? Hold your open hand palm down about 6 inches above the tip of a “soft” butane flame, or a match. You’ll feel the heat almost instantly. This is also why you needn’t touch the tobacco when using a regular butane lighter or match. If it can burn your skin from that distance, imagine what it can do to a razor thin wrapper leaf at close range.
And speaking of matches, if you prefer to use them over a lighter, use a long cedar wood match rather than book matches. They offer a nice aroma when lit, and give you more time to get the job done.
I think the reason so many cigar smokers just “go for it” is that they don’t have the patience to light a cigar in the traditional method, which I’ve summarized below.
Without repeating the whole sequence here, basically it’s a two-step process: Toast the foot entirely, blow on it until it glows all red, then holding the cigar in your mouth at about a 45-degree angle, apply the flame without actually touching the tobacco and puff, drawing the smoke slowly through the head.
The “Flame Thrower”
This is where the cigar smoker clips the cigar, puts flame right to the foot and puffs away. No toasting, just flick the ignition switch and go, usually with fire emanating from the foot like a dragster doing the quarter-mile.
The “Roll, Puff and Blow”
A little closer to the traditional method. The cigar is toasted, then the smoker rotates the cigar while applying flame to the foot and puffing. Once the smoke takes, turn the foot toward you and blow on it. This helps ensure that the entire foot gets lit evenly.
The “Overkill” method
This is similar to the above method except during the toasting process you blow on the foot to see how you’re doing. You notice some black, unlit areas still left on the foot. Normally, you would gently blow on the foot while rotating the cigar to allow these areas to catch. But using this method, the smoker keeps hitting the blackened areas of the foot with the torch flame until they glow like a branding iron. All this does is cause the tobacco to produce more tars, which may turn the cigar prematurely bitter.
The “Torch/Match Switch-A-Roo”
I kind of like this one, though it involves a little extra work. The cigar is first toasted with a torch lighter, followed by a cedar match (or a soft butane flame) to complete the process. The advantage of this is you get the best of both worlds. A cooler flame to toast the cigar followed by a white-hot flame to ensure the tobacco takes completely.
The “Three Matches” method
This is very cool. I saw Gordon Mott do this in a video a while back titled Three Matches. You need three long cedar matches for this one, and it takes a lot of patience.
Important: Do not clip the cigar first! I’ll explain why later.
Light the first match, hold it in close to and in front of the cigar and rotate the cigar as you toast it. Eventually the match will burn down. Be sure to knock-off the ash of the match as you go to keep it burning properly. Put it out and immediately move on to the second match, concentrating on the center portion of the foot as you continue to rotate the cigar. Again, this must be done very slowly. By the end of the third match, the foot should be pretty well lit and emanating a good amount of smoke. At this point, clip the head and draw on the cigar. That’s it!
The reason for not clipping the cigar first is, the gentleman who showed Mott how to do this felt that aromas and flavors coming from the flame source could pass through the cigar and affect the flavor of the tobacco. Personally, I don’t buy it, especially when torch lighters burn so clean. Moreover, Mott admits that he hardly ever uses this technique due to time constraints, but it’s fun to try when you do have the time.
Regardless of how they were taught to light a premium handmade, most cigar smokers eventually develop their own personal method for getting the job done. Sometimes I see someone lighting-up and I want to cringe, but in the end it’s really a matter of to each his own. Or, to look at it another way, when was the last time you corrected someone on how to light their cigar?
Finally, your own personal cigar lighting methods are welcome in the comments field.
Editor’s Note: This post was updated on June 5, 2012.